Writing | # | 100% 0.13sĪvrdude: verifying flash memory against. Reading | # | 100% 0.00sĪvrdude: Device signature = 0x1e950f (probably m328p)Īvrdude: reading input file ".pio\build\ATmega328P\firmware.hex" Lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00Ĭalibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00ĭescription : Atmel-ICE (ARM/AVR) in ISP modeĪvrdude: AVR device initialized and ready to accept instructions Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBackĮeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff With the ICE plugged: avrdude -v -p atmega328p -C C:\Users\Jean-Christophe\.platformio\packages\tool-avrdude\nf -c atmelice_isp -b 115200 -D -P "usb" -U flash:w.pio\build\ATmega328P\firmware.hex:iĪvrdude: usbdev_open(): Found Atmel-ICE CMSIS-DAP, serno: J42700010786Īvrdude: Found CMSIS-DAP compliant device, using EDBG protocol The terminal process terminated with exit code: 1 System wide configuration file is "C:\Users\Jean-Christophe\.platformio\packages\tool-avrdude\nf"Īvrdude: jtag3_open_common(): Did not find any device matching VID 0x03eb and PID list: 0x2141 ![]() With the ICE unplugged: avrdude -v -p atmega328p -C C:\Users\Jean-Christophe\.platformio\packages\tool-avrdude\nf -c atmelice_isp -b 115200 -D -P "usb" -U flash:w.pio\build\ATmega328P\firmware.hex:iĪvrdude: Version 6.3, compiled on at 17:24:16 pio\build\ATmega328P\firmware.hexĪvrdude: usbdev_send(): wrote -22 out of 7 bytes, err =Īvrdude: jtag3_send(): failed to send command to serial portĪvrdude: failed to sync with the JTAGICE3 in ISP modeĭid I install the right driver? should I create a custom board? (I am kinda worried it looks a little complicated to do). So it complains about a missing upload_port argument`. I get: DATA: 0.4% (used 9 bytes from 2048 bytes) It doesn’t seem to change a lot of things when I press upload on platformIO. There was another driver I could’ve installed with a similar name, something like libusbk, I dont know if this one would have been better. now in the device manager it shows up as a libusb-win32 device. This is the driver I installed on my atmel ICE. He also mentioned he made changes to the 328p8m.json file, which would be ATmega328P.json in my case. The solution here was to add upload_flags = -e I searched and found this post, which has the same error message!: Atmega 328 - Internal 8MHZ oscillator - Atmel ICE upload troubles When adding this line to my platformio.ini, I get a different error message: avrdude: Can't find programmer id "atmel-ice"Ģ232HIO = FT2232H based generic programmer Other things I tried: I read on a post (I’m sorry I cannot find the link anymore) that adding upload_port = usbĬan solve the issue. ini file to make my atmel ICE work? thanks! I feel like the message I get : For some development platforms it can be a USB flash drive (i.e. There are some options described on the platformIO documentation Redirecting. The atmel ICE programmer, compared to an Arduino for example, doesn’t have a USB PORT number associated with it, so I don’t know how I am supposed to specify my upload_port argument in my. I tried a couple things described below but I am not sure I am going on the right track. media//)Īt that point I am not sure what to try. PROGRAM: 1.4% (used 444 bytes from 32256 bytes)Įrror: Please specify `upload_port` for environment or use global `-upload-port` option.įor some development platforms it can be a USB flash drive (i.e. ![]() So this is what I wrote in my file: Īnd I get this message as I run the upload command on PIO: DATA: 0.4% (used 9 bytes from 2048 bytes) I first used PIO’s documentation on how to use Atmel-ICE with it on this page: debug-tools/atmel-ice If you would like to use this tool for firmware uploading, please change upload However I cannot upload with my programmer. *I posted this question on stackoverflow earlier but nobody seems to be familiar with PlatformIO enough to answer, so I decided to ask the same question on PIO community directly! I am trying to use my atmel ICE with platformIO and VS Code instead of Atmel Studio, as this software is a pain when I want to use Arduino.h with libraries.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |